Fuselage
|
Fuselage Halves |
Carbon/graphite left & right |
|
Cowlings |
7 piece - bottom, two
top halves, cowl ring, joiner strips, camlocks, intake ducting, air filter and all
mounting hardware |
|
Bulkheads, |
9 fuselage station bulkheads, firewall
and instrument panel |
|
Canopy and Windshield |
Canopy frame, tracks,
crank and all hardware; windshield pieces, frames and all mounting hardware |
|
Intake and Exit Ducting for cooling
systems |
Gear-motor drives for cooling doors and
all mounting hardware |
|
Seats |
Front and Back -
houlder and lap belts for both seats and all mounting hardware |
|
Baggage Compartment components |
|
|
Control System |
Adjustable rudder
pedals front and rear, control sticks, all push-pull tubes, cables and all mounting
hardware |
|
Horizontal Stabilizer |
Spars, ribs, hinge components and all
mounting hardware |
|
Elevator |
Spars, ribs, hinge
components and all mounting hardware |
|
Rudder |
Spars, ribs, hinge components, electric
trim components and all hardware |
|
Adhesive, 2-part
structural epoxy |
|
Landing Gear
|
Landing Gear |
Struts, half-forks, mountings and axles
for mains and tailwheel. Also includes main gear trunnion boxes and all mounting hardware |
|
Wheels, replica
aluminum |
Bearings, seals,
assembly and all mounting hardware |
|
Tires |
6.5 x 8 main gear tires and a 4.10 x 4
tailwheel tire |
|
Triple-puck Brake
System |
Rotors, calipers,
master cylinders all plumbing and all mounting hardware |
|
Actuators |
Al hydraulic cylinders for main gear,
gear doors and tailwheel retraction |
|
Plumbing |
All tubing, fittings,
valves and all mounting hardware |
Engine
|
Engine System, RFI V-12 |
Gear reduction unit and accessory drive
components installed by Papa 51 |
|
Propeller, MT
four-blade constant speed |
Prop governor and all
mounting hardware |
|
Spinner |
Bulkheads and all mounting hardware |
|
Engine Mount, welded
tube steel |
Isolator bushings and
all mounting hardware |
|
Oil & Ethylene Glycol cooling systems |
Oil cooler, radiator, plumbing and all
mounting hardware |
Electrical System
|
Engine electrical
system |
60 amp alternator and
regulator, wiring harness for engine ignition system, Electronic Control Units, switches
and other components |
|
Batteries |
Main and auxiliary batteries and mounting
boxes |
|
Aircraft Electrical
System |
Wire, relays, switches,
breakers, warning lights and other components |
Wings
|
Wing Skins |
One piece top skin and two bottom skins |
|
Main Spar |
Attachment of main spar
to top with skin at Papa 51 |
|
Aft Spar |
|
|
Ribs |
13 each side |
|
Gear Doors |
Inner and outer skins precisely bonded
together at Papa 51, hinges, locks and all mounting hardware |
|
Fuel Tank System |
Vision Micro Systems
fuel quantity probes, gauges, tank sealant plumbing and hardware |
|
Flaps |
Spars, ribs, hinge components, mounting
hardware and electric gear-motor drive |
|
Ailerons |
Spars, ribs, hinge
components, electric trim components and all mounting hardware |
|
Hard Point attachment fittings |
3 tie-down rings and attaching hardware |
|
Pitot tube |
|
|
Wingtips |
All mounting hardware |
|
Adhesive |
2-part structural epoxy |
For an easier understanding of what is included
in the Thunder Mustang kit, the following is a component breakdown. Please refer
questions to